Snapmaker 2.0
Product Feedback Give feedback about Snapmaker devices and addons. Getting Started Get help from fellow creatives.
Topic | Replies | Views | Activity | |
---|---|---|---|---|
2.0 Wiki Content Updates
Dear 2.0 Makers, We will post the related link in this thread once there’s new content for 2.0 in Snapmaker Wiki. Currently, the majority of content for 2.0 is still in the Support Center, but will gradually be migrate… |
![]() ![]() ![]() ![]() |
18 | 3076 | August 26, 2024 |
Collection Of Guide Links
I figure it might be good to start a topic that sort-of compiles useful guides together to make them easier to find, since the forum doesn’t allow signatures and guides can just disappear into the void. As such, in this … |
![]() ![]() ![]() ![]() ![]() |
13 | 5240 | January 3, 2025 |
Summary: Extruder calibration a must
The topic known as: has become very useful to point people to so that they can calibrate their e-steps. However, that topic has become a bit large and overwhelming for a newcomer. So I’m starting this topic as an easie… |
![]() ![]() ![]() ![]() ![]() |
36 | 19978 | January 31, 2025 |
Snapmaker 2.0 Firmware Updates and Downloads
We will release the latest Snapmaker 2.0 firmware updates and downloads under this topic. Your feedback is very much appreciated. You can report any bugs or make any suggestions in the discussion thread. Snapmaker 2.0 F… |
![]() ![]() ![]() ![]() |
35 | 150466 | July 18, 2024 |
How do I use the recover from power loss feature? |
![]() ![]() ![]() ![]() |
4 | 1090 | April 1, 2025 |
What to use as an air blower for CNC aluminum cutting? |
![]() ![]() ![]() ![]() ![]() |
11 | 165 | March 31, 2025 |
Newb question about dual color model |
![]() ![]() ![]() |
3 | 65 | March 31, 2025 |
Quick Swap Fillers 40W and 2W IR |
![]() ![]() |
2 | 70 | March 30, 2025 |
1064nm IR+20/40W + Lightburn Guide |
![]() ![]() ![]() ![]() ![]() |
55 | 3054 | March 29, 2025 |
40W laser Cross Hair |
![]() |
0 | 32 | March 29, 2025 |
Nozzle replacement |
![]() ![]() ![]() |
3 | 87 | March 28, 2025 |
Troubleshooting 3DPrint Quality |
![]() ![]() ![]() |
5 | 58 | March 26, 2025 |
Collection of SM 2.0 Picutres and Mods - Post Your Setup! |
![]() ![]() ![]() ![]() ![]() |
5 | 448 | March 25, 2025 |
Cleaning out the laser |
![]() ![]() ![]() ![]() ![]() |
15 | 186 | March 25, 2025 |
I did some mods for my enclosure and want to share them with you |
![]() ![]() |
1 | 212 | March 21, 2025 |
Setting up a camera a-350 |
![]() ![]() ![]() ![]() ![]() |
7 | 209 | March 20, 2025 |
[GUIDE] How to install apps on your Snapmaker 2.0 LCD - Access Android part of LCD |
![]() ![]() ![]() ![]() ![]() |
40 | 1016 | March 20, 2025 |
Lightburn and air assist on the 40W laser |
![]() ![]() ![]() |
6 | 97 | February 23, 2025 |
Purge Bucket and Nozzle wipe mod |
![]() ![]() ![]() |
7 | 636 | March 20, 2025 |
Dear Snapmaker enthusiast & People in Snapmaker |
![]() ![]() ![]() ![]() ![]() |
6 | 208 | March 19, 2025 |
My Support rails and debris catcher |
![]() ![]() |
2 | 108 | March 19, 2025 |
How to set home position for laser module very precisely - and keep this home position for subsequent jobs |
![]() ![]() ![]() ![]() ![]() |
18 | 303 | March 19, 2025 |
Snapmaker 2.0 40W Laser Test - Speed V Laser Power |
![]() ![]() |
3 | 59 | March 18, 2025 |
Freecad Post Processor for CNC jobs - Error messages, no gcode file |
![]() ![]() ![]() ![]() ![]() |
7 | 1516 | March 17, 2025 |
CNC Manual Jog Controller for Snapmaker |
![]() ![]() ![]() ![]() ![]() |
12 | 281 | March 17, 2025 |
Laser Save origin and focus for multiple copies |
![]() ![]() ![]() ![]() ![]() |
6 | 600 | March 15, 2025 |
Cabinet wiring pin assignments |
![]() ![]() |
2 | 51 | March 15, 2025 |
SM350 Laser and slightly warped stock |
![]() ![]() ![]() |
2 | 60 | March 15, 2025 |
3d module filament latch doesn’t close |
![]() ![]() ![]() ![]() ![]() |
16 | 124 | March 13, 2025 |
A-350 won't turn on with x-gantry plugged in |
![]() ![]() ![]() |
3 | 31 | March 13, 2025 |