Snapmaker Ray
Topic | Replies | Views | Activity | |
---|---|---|---|---|
Early Preview of the Ray 40W
Hi All. I’ve been lucky enough to get my hands on a Ray 40W + Enclosure delivered early to play, test, provide honest feedback, and share with ya’ll my findings and fun times! I will update this Thread with my journey … |
40 | 1593 | March 25, 2024 | |
Snapmaker Ray + Lightburn
John over at Lightburn has made a thread on the Lightburn forums on using the Ray. It includes profiles and setup. The thread can be found here; While I don’t have the Ray or 20/40W module, I figured I’d share it over … |
13 | 850 | March 8, 2024 | |
Discussion of Snapmaker Ray Firmware Updates
This thread is for discussion of the Snapmaker Ray Firmware Updates. |
9 | 453 | March 15, 2024 | |
Snapmaker Ray Firmware Updates and Downloads
We will release the latest Snapmaker Ray firmware updates and downloads under this topic. Your feedback is very much appreciated. You can report any bugs or make any suggestions in the discussion thread. Snapmaker Ray F… |
4 | 882 | January 26, 2024 | |
About the Snapmaker Ray category
|
3 | 282 | August 4, 2023 | |
My First Experience's With The 40W Ray (Not Good)
|
11 | 162 | April 26, 2024 | |
10W Laser Module Quick-Swap Plate and Calibration Target Model for Snapmaker Ray
|
3 | 459 | April 22, 2024 | |
Install a new fan with better efficieny and lower noise?
|
5 | 89 | April 22, 2024 | |
10W laser in Ray System
|
2 | 53 | April 20, 2024 | |
Color Laser Marking on Stainless Steel, Using the Snapmaker Ray 40W Laser Module
|
4 | 199 | April 10, 2024 | |
Targeting Cross Hairs
|
3 | 102 | April 10, 2024 | |
Laser won't go back on after flame detection is triggered, unless power is cycled
|
3 | 326 | April 6, 2024 | |
Ray 40 w Alarm Keeps Firing
|
4 | 277 | April 2, 2024 | |
Snapmaker Ray 40W work origin problem
|
6 | 374 | April 2, 2024 | |
Do Any Other GRBL Rotary Modules Play Nice With Snapmaker?
|
0 | 59 | April 2, 2024 | |
Ray - postprocessor Fusion 360
|
0 | 52 | March 26, 2024 | |
Setting up lightburn to use negative y cordinates on ray
|
0 | 50 | March 21, 2024 | |
Enclosure not removing smoke
|
0 | 62 | March 19, 2024 | |
Insufficient blower capacity
|
15 | 173 | March 18, 2024 | |
Operating time counter
|
0 | 58 | March 16, 2024 | |
Open enclosure door support
|
5 | 107 | March 12, 2024 | |
New to Ray - Rotary Module and Emergency Button
|
14 | 584 | February 29, 2024 | |
Run issues after Wifi reboot
|
3 | 61 | February 29, 2024 | |
I am not sure if I assembled the "REY" correctly. Is the cutting area outside of the laser working area?
|
2 | 69 | February 23, 2024 | |
Cross line laser
|
1 | 145 | February 8, 2024 | |
Help with Origin Issue on New Ray
|
8 | 555 | January 27, 2024 | |
Luban does not connect with Snapmaker Ray
|
3 | 115 | January 25, 2024 | |
Luban showing enclosure connected
|
0 | 73 | January 21, 2024 | |
Extra square added to upload
|
2 | 159 | January 20, 2024 | |
10/20/40 Watt Laser Material Settings
|
7 | 3562 | January 15, 2024 |